The sectors are transferred through the Data Register 16 bits at a time. Page 83 – Table 51 Command table for device lock o A value of h indicates that there is no General Purpose Log Directory. The Error Log Index indicates the error log data structure representing the most recent error. In CHS mode, this register contains native max cylinder number.

Uploader: Fausho
Date Added: 15 September 2006
File Size: 20.34 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 84146
Price: Free* [*Free Regsitration Required]

These error logs are bytes in length and retain the last 31 errors that occurred during any Hitachi hdp725032gla360 Data hdp725032glx360. In CHS mode, this register contains max cylinder number which is set. Figure 27 Connector Locations 5.

The timeout interval will be reinitialized if there hitachi hdp725032gla360 a drive access before the timeout interval expires. Then user data is erased.

Automatic Off-Line Data Collection, but the device may respond with the error code specified in Table on the page. Page Automatic Off-Line Data Collection, but the device may respond with the error code specified in Table hitachi hdp725032gla360 the page.

Don’t have an account? Security Set Password f1hTable Security Set Password Command f1hSecurity Set Password f1h This command requests a transfer of a single sector of data from the host including the information specified in Table on page Page If a software or hardware Reset is issued to the device before all of the microcode segments have been transferred to the hitachi hdp725032gla360 the device shall abandon all of the microcode segments received and process the Reset.

Instead, the register contains a diagnostic code, refer to Error Register Diagnostic codes in Table 48 on page 65 for its definition.

Erase mode 1- Enhanced, 0- Normal. The device will transfer a sector to the host containing the information described in the following pages. The actuator assembly is balanced to allow vertical or horizontal mounting without adjustment. When set to one, off-line scan after selective test is hitachi hdp725032gla360. If the feature set associated with the log specified in hitachi hdp725032gla360 Sector Number register is not supported or enabled, or if the values hitachi hdp725032gla360 the Sector Count, Sector Number or Cylinder Low registers are invalid, the device shall return command aborted.

Command Abort is returned see abort conditions for Error Register.

The Idle Immediate command will not affect to auto power down timeout parameter. To determine command timeout value, Word 89 of Identify Device data should be referred. hitachi hdp725032gla360

HDD鐃緒申鐃緒申 の編集

hitachi hdp725032gla360 Set Max commands are hitachi hdp725032gla360. Commands disabled by Set Max Freeze Bdp725032gla360 are: The value of the General Purpose Logging Version word shall be h. This bit is not driven and will always be in a high impedance state. So the host system can confirm the completion of write cache operation by issuing Soft reset, Standby Immediate command or Flush Cache command to the device before power off.

The Error Log Index indicates the error log data structure representing the most recent error.


Page 46 – Figure 20 Jumper positions for 15 logica The valid range for attribute thresholds is from 1 hitachi hdp725032gla360 decimal. The termination resistors on the device side are implemented on the drive side as follows: The Read FPDMA command reads one hitachi hdp725032gla360 more sectors of data from disk media, and then transfers the data from the device to the host.

Hdp725032gka360, Caution, References General 1.

If cleared to zero, a request to remove a previous configured stream is specified. Default value is h. Word 86, bit 3 indicates that Advanced Hitachi hdp725032gla360 Management is enabled if set.

Set Features hitachi hdp725032gla360Table Set Features Command efhSet Features efh The Set Feature command is to establish the following parameters which affect the execution of certain features hitachi hdp725032gla360 shown in below table. Erase mode 1- Enhanced, 0- Normal Page If a command is marked by the host as high priority, the device shall attempt to provide better quality of service for the command.

HDD鐃准・申鐃緒申鐃緒申鐃殉・申鐃淑わ申鐃駿てメ・申鐃緒申鐃緒申鐃出象)わ申HDD鐃緒申鐃緒申 の編集

Table Self-test Log Data Structure After 21 hitachi hdp725032gla360 have been recorded, the oldest descriptor will be overwritten with new descriptor. After power on reset or hdp725032gla306 reset, the device is set to the following features as hitachi hdp725032gla360. These command timers are volatile. The device is unable to read its Attribute Values or Attribute Thresholds data structure.

hitachi hdp725032gla360 Page After power on reset or hard reset, the device is set to the following features as default. Set Max Unlock commands are rejected until a hard reset or a power off. Streaming Feature Set If a host requests flushes at times other than the end of each Allocation Unit, streaming performance may be degraded.

Height mm Width mm Command execution time depends on drive capacity. It is not required that devices process all high priority requests before satisfying normal priority requests. Sata Bist built-in Self Hitachi hdp725032gla360Sata Interface Power Management The device supports hitadhi receiving hitavhi interface power management requests and initiating hitachi hdp725032gla360 power management.

This command writes a specified number of byte data sectors to the specific log. If the host attempts to write to a read only log address, the device shall return command aborted. Page 83 – Table 51 Command table for device lock o When the address requested is equal to or less than ,, words Table Erase Unit Information The execution time hitachi hdp725032gla360 this command is set in word 89 of Identify device information.

The Identify Hitachi hdp725032gla360 command requests the device ihtachi transfer configuration hitachi hdp725032gla360 to the host. Single track seek is measured as the average of one 1 single track seek from every track with a random head switch in both directions inward and outward.